直立連簾使用說明書(EN)

BINTRONIC ENTERPRISE CO., LTD

No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)

Email: [email protected]

This instruction manual version is v1.0.

How to open Battery Compartment Cover

How to replace Battery Compartment Cover

Motorized / Smart Vertical Blinds

Instruction Manual

1-1 Travel Distance Setting and Revising

2-1 Adding another Remote Control Unit

3-1 Clear Off Password

4-1 Externally connected Manual Switch Box

5-1 Battery Replacement

5-2 Product Specifications

5-3 Quick Setting Index

5-4 Instructions for using Remote Control Holder

OPEN

STOP

RIGHTWARD

LIGHT FILTERING

LEFTWARD

LIGHT FILTERING

Push the cover out

Insert latches into

corresponding slots

Place Battery

Compartment Cover

to engage it with Slides

1 2 3

Insert latches

making settings

Key check-points prior to

Make sure the slats of Vertical Blinds are

installed properly before setting.

If six beep sounds occur during the setting, it means that the setting is not completed yet;

it might because there is power failure during the setting or [STOP] is accidentally pressed.

Please go back to step 1-1 to reset.

Press [OPEN] + [SET] keys

until a short beep sound occurs.

the curtain begins to set the

travel distance automatically

STEP-1

1 2

1-1 Travel Distance Setting and Revising

STEP-1

back

a short beep sound occurs

a long beep sound occurs

steps:

the curtain closes completely

the slats are turned leftward and rightward

the curtain opens completely

the curtain closes and opens completely again

A long beep sound will occur, indicating that

the travel distance setting is completed.

Please repeat step 1-1

if there is something wrong

with the travel distance of the curtain.

Setting Completed

P.1

(1) When the curtain is moving, press [STOP]

to stop the curtain.

(2) When the curtain is not moving, press [STOP]

to flip the slats to the center position.

Press and hold [SET] until three short beep sounds occur,

indicating that the setting mode of Adding another Remote

Control Unit is activated.

STEP-1

Now press [STOP] key of the Remote Control to be added;

the adding process is completed when a short beep sound occurs.

STEP-1

STEP-2

STEP-1

three short beep sounds occur a short beep sound occurs

Motorized / Smart Vertical Blinds

Instruction Manual

P.2

2-1 Adding another Remote Control Unit

3-1 Clear off Password

back

After the setting is completed, a long

beep sound will occur, indicating that

the setting mode is deactivated.

Setting Completed

When everything is done,

only the password of this

remote remains, others will

be erased. If a new password

is not added, the old password

will not be erased.

Setting Completed

unplug power supply wait for 15 seconds resume power supply beep sounds occur beep sounds stoppress 4 keys altogether within 8 seconds press [OPEN] + [CLOSE] within 5 seconds

Unplug power supply of the Motor, wait for 15 seconds, resume power supply of it. Within 8 seconds, press [OPEN] + [STOP] + [CLOSE] + any

of blank keys [LEFTWARD LIGHT FILTERING] OR [RIGHTWARD LIGHT FILTERING] altogether 4 keys, beep sounds will occur immediately,

then, within 5 seconds, press and hold [OPEN] + [CLOSE]. The beep sounds will then stop, indicating that the password is cleared off.

BINTRONIC ENTERPRISE CO., LTD

No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)

Email: [email protected]

This instruction manual version is v1.0.

flat side (positive +)

latched up by

two spring plates

Completed.

Motorized / Smart Vertical Blinds

Instruction Manual

4-1 Externally connected Manual Switch Box

5-1 Battery Replacement 5-2 Product Specifications

yellow

red

brown

green

System Manual Switch

Green: Common

Brown: Open

Red: Stop

Yellow: Close

A brief contact will activate the function;

DO NOT short-circuit continuously.

Instructions

Green + Brown = open the curtain

Green + Yellow = close the curtain

Green + Red = if the curtain is moving, it will stop immediately.

= if the curtain is not moving, the slats will be turned.

REMINDER The slats cannot be turned if the current position of the curtain is at 1/4 of the total travel distance.

Green + Brown + Red = the curtain turns left; the slats open.

Green + Yellow + Red = the curtain turns right; the slats close.

With flat side (positive +) of the Battery facing upwards,

making sure that the Battery is latched up by two spring plates,

insert Battery in a slanted angle to enter it into the Battery Holder.

1 2

Battery: CR2450 3V (One-time type lithium battery)

Dimensions: L 13CM, W 4.8CM, H 1.1CM

Standby Current: <1uA

Modulation Method: OOK

Encoding Method: Internally-burnt fixed coding

Transmission Frequency: 433.92MHz

Antenna Type: on board, Gain=0 dbi

Weight (including battery): 66g

BINTRONIC ENTERPRISE CO., LTD

No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)

Email: [email protected]

This instruction manual version is v1.0.

Motorized / Smart Vertical Blinds

Instruction Manual

P.4

5-3 Quick Setting Index

5-4 Instructions for using Remote Control Holder

Travel Distance Setting and Revising:

(1) Press [SET] + [OPEN] keys, the curtain begins to set the travel distance automatically.

(2) A long beep sound will occur, indicating that the travel distance setting is completed.

Adding another Remote Control Unit:

(1) Press [SET], three short beep sounds will occur.

(2) Then press (Remote Control 2) [Stop], one short beep sound occurs, indicating that the setting is completed.

Clear Off Password:

(1) Press [OPEN] + [STOP] + [CLOSE] + [LEFT LIGHT FILTERINF] or [RIGHT LIGHT FILTERING] altogether 4 keys. Beep sounds will occur immediately.

(2) Then, within 5 seconds, press [OPEN] + [CLOSE], the beep sounds will stop, indicating that the setting is completed.

Vertical Holder Wall-mount Holder

Open-up support plate on

the back for the use as a

vertical holder.

open up

Apply the provided double-face

adhesive tape on the back of

Holder and stick it onto the

desired position on the wall, as

a wall-mounted holder.

Apply the adhesive tape

stick it onto the

desired position

BINTRONIC ENTERPRISE CO., LTD

No.62, Bengong 5th Rd., Gangshan Dist., Kaohsiung City 82059, Taiwan (R.O.C.)

Email: [email protected]

This instruction manual version is v1.0.